Category: Fuel System Upgrades

on

Want an electric fuel pump to last forever and work right? We’re going to show you how to install it and wire it up the correct way!

OK, let’s talk about electric fuel pumps. There is a lot of confusion and misunderstandings about them. There is also a lot of potential danger when people don’t do it right. The reason is, they don’t know the right way to plumb them in or wire them.

So, let’s break it down:

When do you need an electric fuel pump?

Is an electric fuel pump reliable?

How do you keep an electric fuel pump safe?

How should you wire an electric fuel pump?

Deference between Mechanical and Electric Fuel Pump.

When do you need an electric fuel pump?

Usually, a preferable mechanical Fuel pump over an “aftermarket” electric pump. They tend to be more reliable. But, sometimes that won’t work.

In my old ’47 Chevy, the engine I had swapped in had an issue. The cross member was in the way of the mechanical Fuel pump. So, I ran an electrical pump and had many trouble free miles.

Sometimes, people will plumb them inline with a mechanical fuel pump. They add more volume and pressure. This is more for a full on drag car though.

Is an electric fuel pump reliable?

Yes, they are. Hey, there’s about a billion cars running around right now with them. All new cars have them.

With aftermarket pumps though, YOU have to install them. That’s where some problems can start.

We’re here to show you the right way to do it!

So, what do I use? For a stock or performance street car, I like these Facet/Purolator pumps from Napa. They are quiet and work well.

A lot of people complain about some aftermarket pumps being junk. But usually, there is a reason they go out. It’s often the way the person installed it. There are a few things that kill them.

-Do not run them dry.

-Always run a filter before the pump.

-Keep them as close to the tank as you can. An electric fuel pump pushes fuel much better than they can pull it.

-Mount them away from heat sources such as exhaust.

-Electrical power to them is everything. You must have the correct wire size to it. A relay is preferable for users. You may be getting the proper voltage to it, but not enough amps. Remember, the longer the run the more the power will drop.

-Also, the grounding of it is critical. Many people will scrape the area where they mount it or even add a ground wire. But, they forget that they don’t have a good ground from the body to the frame or to the engine. This will kill pumps real quick.

Tip: Screw into metal to the ground, not through it. “Star” washers are your friends…

Run a ground wire to the front. Many professional auto electricians will run ground wires. They use from a unit to a common grounding point in an older car, like in a fiberglass car. That way, there is no question if your ground is good, and it’s only 1 extra wire.

Once, a buddy and I were going to a show in his ’26 Buick roadster. It workers built it much like a T-bucket and it had an electric fuel pump. Its wires were incorrect manner and grounded by screwing into the frame by the pump. We were about 50 miles out, and the pump quit.

Hmmmm…

What happened was the older metal of the frame.  It wasn’t carrying the current well enough. The pump overheated and shut down.

It’s fortunate enough, he had some extra wire. which we screwed one end to the ground wire at the back. And ran it to the front where we attached it to the negative side of the battery.

The pump started back up after it cooled down and we were trouble-free all the way there and back. When we got home he wired it in correct and never had a problem after that.

But they don’t have to be.

If something lets go in your engine bay like a fuel line, the engine will quit in a dramatic way. But, if you don’t have a way to automatically shut off your electric fuel pump. you will keep spraying raw fuel all over your hot engine and wiring.

Also, in a crash, your pump can continue to run feeding a fire if you don’t have a way to stop it.

Note: Never mount an electric fuel pump in an enclosed area such as the trunk or interior space.

OK, so how do I do it right?

The easiest way is to use an oil pressure switch. The switch will stop the pump whenever the oil pressure in the engine goes away. So, whenever the engine is off, the pump will turn off in a very automatic.

Some switches do that. But how do I get the pump to run when I’m trying to start the motor and the oil pressure’s not up yet?

You use a three prong switch like this Standard Ignition PS-64:

The switch will also let the pump run when you hit the starter because the engine doesn’t have oil pressure yet.

One wire goes to the pump, one to the start circuit, and the other to the ignition circuit. So, when there is no oil pressure, the switch connects START to PUMP, and as soon as you start cranking it runs the pump. When the oil pressure comes up, the switch connects IGN to PUMP, for normal running. When oil pressure goes away (because you hit that rock and tore the pan off the engine. For example) it again connects START to PUMP and disconnects IGN from PUMP, so the pump shuts off.

Don’t worry, it’s easy to wire.

How should you wire an electric fuel pump?

Since you need the fuel pump back by the tank. At the same level as the fuel or lower, that usually means you’re going to have a long run of wire. So, you need to have a good wiring going back to it. Wiring that will carry enough current. Running the current through your ignition switch isn’t a good idea. since it’s already overloaded, and will kill the voltage. That will kill the pump. It’s nice for convenience. That’s why a relay is good to use.

It lets the ignition switch activate the pump, while keeping the power from having to run through it. It will keep your pump alive and happy because it is getting full voltage. A good way is to mount a relay beside a power distribution block on the firewall. (see Improved Power Circuit) and get the power from there.

Here is a diagram on how to wire and plumb your pump:

on

MSD Performance  Atomic Fuel Injection System  has been granted an Executive Order Number from the California Air Resources Board. This E.O. Number makes the Atomic the only aftermarket EFI system that is legal on 1987 and older GM vehicles in California. The Atomic EFI system received E.O. Number D-722 which permits the system to be installed in place of the factory carburetor on 1987 and older  passenger cars and trucks originally powered by a V8 engine. This Executive Order also means the Atomic EFI system provides “reasonable basis” for satisfying the anti-tampering requirements of the Federal Clean Air Act, thus allowing its use in all other states. This is terrific news for enthusiasts with an ’87 and older  car or truck as it means they can finally do away with their old carburetor and take advantage of the driveability benefits of a modern, self-learning EFI system such as quick starts, consistent idle and smooth power throughout all driving conditions. MSD will supply an information label with the E.O. Number and details that must be affixed on the vehicle for inspection purposes. Great news for all you Hot Rodders and Replica cars that faced restrictions with Emmisions.